Automotive Locksmith - Get Professional Locksmith Services Now!

The Saturn vehicles usually use a small metal lock cylinder to ensure that cargo stored in the trunk. If the trunk has been damaged, generally the cylinder will be damaged also and it must be replaced. Replacing the Saturn vehicle’s lock cylinder is capable within the skills of most vehicle owners. You simply need a few simple tools and few hours.

Here are the steps on how to remove a Saturn trunk lock.

1. Cut the ground cable from the negative terminal of the battery by loosening the bolt and pulling the clamp off to the negative battery terminal.

2. Unclasp the trunk.

3. Eliminate the upholstered panel from the trunk cover. By the use of flat-blade screwdriver, slowly force the panel away from the trunk cover.

4. Cut the actuating rod from lock cylinder by moving the clip away from the rod. Pull the rod from the lock cylinder.

5. Eliminate the lock cylinder clip. Pulling the clip straight up, use needle-nose pliers.

6. Eliminate the lock cylinder from the trunk cover by pulling it towards the back of the car.

Here are the steps on how to install a new Saturn trunk lock

1. Place the new lock cylinder in the hole of the trunk cover.

2. Reinstall the lock cylinder clip by moving it over the top of the lock cylinder.

3. Place the actuating rod into the lock cylinder’s back. Move the clip over the rod.

4. Reinstall the trunk cover upholstered panel by putting it in position on the trunk cover and pushing the plastic clips into trunk cover hole.

5. Connect again the ground cable to the negative terminal battery by moving the clamp over the negative battery terminal and tightening the bolt.

If you need a trunk lock to match your car door locks, you will have to buy a complete set of lock for your car and change the other lock cylinders also. If you don’t want to take on this job by yourself, find a car locksmith near you who can help!

How to Repair a Car Ignition Switch

admin — Mon, 10 Oct 2011 19:31:00 +0000

The best way to repair the car ignition system is to replace it.The ignition system is a device that triggers your car engine. If your car engine is triggered means then only, you will be able to drive a car. Car will not be able to start if there is some problem in the ignition system. So it’s required that the owner of a car deals well with your ignition system problem very soon to make it work. In this article we are going to discuss, what is the function of the ignition switch and how we are going to deal if there is problem in the ignition system. If your car ignition switch is dead to some problems , then you will be not able to start your car until you troubleshoot the problem in ignition switch device of your car. To deal the problems in ignition switch in car , one needs to know the working principle and structure of the car.

The ignition switch in a car is two connected device. Where one is inside lock cylinder were you will have to insert your car key and start and the other is electronic switch , which is at back of the cylinder. The arrangement of cylinder will be not similar in all cars for the electronic switch. The main function of the car ignition switch is to start the car. Nowadays the modern car ignition switch systems come in vary wide range in different cars. The options actually available in car ignition switch system is that ON and OFF , and lock. The ON option is loaded with spring when you put the key and turn it starts the car engine.

The main symptom of the ignition switch that everyone can find out in their cars is that starting trouble. The symptoms may be due to low battery power. And the bad starter device fixed to start the car. The best way for one to deal the ignition switch problems is to check the car battery. The car battery is actually checked with an voltmeter , if the car battery works properly , then there is no problem in ignition switch and the car works properly. To start the car engine , working of the ignition switch is very important. If the problem occurs vey often even after troubleshooting the problem, then it’s better to replace the ignition switch of the car with a new one like locksmith installed ignition switch. The problem mostly lies in the electric board in the ignition switch if it’s not working properly. While rectifying the problem in switch make sure that the car starter gear is being disengaged. The problem in ignition switch may be mainly due to improper functioning of the cylinder which is locking. Otherwise it may be due to the electrical switch beneath the ignition switch of the car. So if one has have no problems in his car starting means, the best option for them is to repair or install the locksmith ignition switch.